|
|
| Romy the Cat's
personal site dedicated to advanced audio and evolved music reproduction
techniques
|
|
 |
|
|
|
|
|
[quote user="N-set"] I do have some serious concerns with respect to my design, the LF stability beeing the most important one (before we even approach talking about the Sound...if any); you may rememebr I was asking you about the stability and relia...
|
|
[quote user="cv"]Here's a crazy thought... have you every tried driving the S2 directly from the Placette?! I know the 6E5p does some unique things but I wonder if it might be educational.The placette has a 7 ohm Zout right? Don't forget that that do...
|
|
Paul, 6E5P may strech very much, but maybe just enough to close the gap. In such a racing car there is a little margin, it's not a usual 10W+ design. Biased at -3.5V 6E5P will produce +40Vmax on the grid, driver driven to the limitThe grid will eat ...
|
|
Yes, decoud, the 6e5p-GM70 is an easy amp but 6e5p is a hell of voltage driver and I do not feel that a single 6e5p will be able to drive GM70 into grid currents. If people use dead speakers and need a lot of power than use the ability of direct hea...
|
|
peter wrote: By "dynamic viscosity" do you mean the reluctance of an amplifier to be dynamic, i.e., the degree to which an amplifier sounds like it is bogged down, usually as a result of a poor rise time on transients, i.e., poor HF response, or a tu...
|
|
[quote user="cb"] The bias voltage I get on the 6e5p is around minus 4.4v on both the circuits. This is with the inputs shorted. With the inputs connected to adjust voltage to 0.0mvdc, I get a reading of plus 0.4vdc. This is with VR1 set at maximum (...
|
|
Now I re-listen all the things the we try to measure. To surmised everything I have to tell that Dima’s way to looks for optimum operation point of the tube (setting balance for voltage vs. current sufficiency) turned out to be very successful as I d...
|
|
Paul, I know NOTHING about pentodes. I looked at the curves:at 1500V/300mA/-85V loaded with 3.2k will give a whooping 190Wwith +/-85Vmax swing, staying in A1. At 2.4k this drops to 155W.G2 @500V, eating 50mA of current(!)But the linearity...???? The ...
|
|
AlloWell this could be very interesting.... the Melq driver (at lower voltage) direct coupled to a 6C33 cathode follower run at low voltage, high current. Vincent looks like he's running about 80V 500mA, though in this case you'd need to use a r...
|
|
Since I know about a few ongoing attempts out there by different people to build Melquiades I would like to share with some of my observations regarding corrections, simplification and possible modifications of Melquiades amplifier.
Obviously you ha...
|
|
Contemplating now how to organize biasing for 3 singe stages of my 6-chanls amp I was faced the dilemma: do I need to bias my tubes. The 6E5P/6E6P are Russian tubes and it means that are very different right from the boxes. The Milq, driver tubes, be...
|
|
The 6sn7 is a fine amplification tube for use in preamps or gain stages, but it has way too high of an output impedance for driving power tubes. This is my personal preference. It also depends greatly on the topology. Maybe George u...
|
|
Another decision that I need to make about the new Super Milq. I have MF and Fundamental Channels around the Vitavox S2 drivers that will be driven directly from the single-stage amplifiers, with the crossovers and attenuators sitting at amplifier li...
|
|
Hey Cat,Well..my first question would be regarding the application. The big Melq tube is already doing the bass towers...is it not enough current? And wouldn't a proper class A 100w amp with its low low efficiency require something like 1...
|
|
[quote user="anthony"]Hi Romy,So, six channels are now operational in the first DSET. By up I mean the anode voltages on all tubes is about right and the currents are in the ballpark of where they need to be. I am yet to check the DC Offset so hope...
|
|
[quote user="be"]Thanks ml8, do you know how much it could swing before problems, either due to clipping or grid current?[/quote]
I would be interesting to know how much plate voltage (and power) 6E5P would have with no bias. If ml8 would promi...
|
|
Ok, I just read your "Melquides Remote biasing". This technic can not be duplicate in my amp due to DC coupling, the C3G (I dont use 6E5P) driver stage basically adjust the 6C33C current in the output stage. Just for curiosity, I will build a mono bl...
|
|
Romy, Big thanks for your answers. But i've got another question :)You mentioned gas regulator as grid current "absorber".Very good point, because personally i hate to use resistor as a grid leak.Instead of it i'll use choke - almost with any tube, i...
|
|
Romy, I'm of course familar with your MF design and Jim's 6E5P curves is what I base my considerations on at this moment (along with the corresponding Spice model).Your DHT MF is quite self-balancing due to the large cathode resistor. WhatI have in m...
|
|
I think it should be somewhere posted for my and perhaps for others future references. Here is the setting for testing Melquiades' single-stage tubes on Hickok 580/580A tube testers. To test the tube as a driver for a full Milq (two stages) set ...
|
|
Jim, I have sent you the tubes – it might be an interesting journey.
I send you:
1) 6C33C that was working with both cathodes approximately a year. It is not dead year but it is deep into retirement age. Run it at 220V and 200-250mA full-tube,...
|
|
My project to add 3 one-stages channels to Super Melquiades look like progressing (it means I will have the new 15,5:1output transformers very soon) and in context of upcoming changes and, after long consideration and some tests, I desire...
|
|
.. and therefore I do not know how serious to take you.As far as I know as now there are no people who have built Melquiades. I know that up to now about 5 attempts to do it but no one finished it yet up to the point that might report result. Dima is...
|
|
Yes, Daniel, this resistor is somewhere between 30R and 100R, the value is not truly important. The purpose of the resistor is to slightly decouple the potentials of plate to grid, it cares no current and you might use 1/8W resistor or even less. BTW...
|
|
Well, it is not necessary a fully qualified urban legend as the problem does take please with fixed based 6C33C but..... only under certain conditions. I have written about it a lot on my site but will very briefly recall it again.
Dima might be cor...
|
|
Here is the general specification for the parts that I used. The selection of the parts implies some liberty of course. It will be your amp after all, not mine - do whatever you wish. In some case when I feel that requirement is critical I will stres...
|
|
[quote user="N-set"]Risking that the topic has already been discussed and that I postin a wrong category (Romy feel free to (re)move this post:Is there any sense in trying 6C33 at higher volatges and lower currents?More precisely, I've been wondering...
|
|
[quote user="drdna"]You want a suggestion for a good 2A3? Get Ricardo Kron's (KR Audio Enterprises) KR 2A3. Very rugged, overbuilt. There is no comparison between this tube and all other 2A3's, and I tried many of them. The sound is more dynamic, the...
|
|
[quote user="Paul S"] Which caps exactly did you decide to try? I don't recognize the big black jobbies. Are they oilers? Are they 200V? [/quote]
I did not “decide” but went with what I had in my hands. They are the Ansars from the...
|
|
Hi Cat,It seems the 6e5p is driving the transformer directly. I've used various versions of even simple mosfet followers to good effect at the headphone level, but never considered using a speaker level transformer. Did you and Dmitry cons...
|
|
|
|
|
All context of this site except the Forum's posts
Copyright © Roman Bessnow 2004-2024
All messages within the Site’s Forum Copyright © by
authors of the posts
|
|
Last 24-hours posts: |
0 |
|
 |
|
|
Total human visitors: |
42,798,050 |
|
|
|
|
|
|